Pull the square wire (A) to the left and right, then apply a
force in the direction of the arrow to cut off the residual sealant on
front edge (B).
•
Make sure that you put on gloves to protect your hands from potential injury.
•
Be careful about potentially burning your hands due to the heat generated from the wire in use.
•
Be careful when working with wiring because it may be cut.
•
Be careful not to damage the body.
•
Make sure that two or more people work together when using wires.
9.
Push wire (A) from the outside of the body toward the face of edge (B) in the direction of the arrow.
10.
When wire lead is visible inside body, pull wire lead (A) toward inside.
11.
Pull the square wire (B) to the left and right, then apply a
force in the direction of the arrow to cut off the residual sealant on
front section (A-A).
–
B(1): Work inside car
–
B(2): Work outside car
•
Make sure that you put on gloves to protect your hands from potential injury.
•
Be careful about potentially burning your hands due to the heat generated from the wire in use.
•
Be careful when working with wiring because it may be cut.
•
Be careful not to damage the body.
•
Make sure that two or more people work together when using wires.
•
When using wires to remove the residual sealant, there may be
an interference between the nut hole and device hole. Thus, perform
sealant removal work as shown in the following figure:
Use a scraper or flathead driver to lift up a region between the body and panorama sunroof.
Turn and pull out wire (A)
between the nut hole and device hole (B) in the direction of the arrow.
Next, cut off the residual sealant again.
•
Be careful to avoid damaging the nut hole (C).
•
Be careful to avoid damaging the device hole (D).
12.
Pull the square wire (B) to the left and right, then apply a
force in the direction of the arrow to cut off the residual sealant on
side section (A-A).
–
B(1): Work inside car
–
B(2): Work outside car
•
Make sure that you put on gloves to protect your hands from potential injury.
•
Be careful about potentially burning your hands due to the heat generated from the wire in use.
•
Be careful when working with wiring because it may be cut.
•
Be careful not to damage the body.
•
Make sure that two or more people work together when using wires.
13.
Pull the square wire (B) to the left and right, then apply a
force in the direction of the arrow to cut off the residual sealant on
rear section (A-A).
–
B(1): Work inside car
–
B(2): Work outside car
•
Make sure that you put on gloves to protect your hands from potential injury.
•
Be careful about potentially burning your hands due to the heat generated from the wire in use.
•
Be careful when working with wiring because it may be cut.
•
Be careful not to damage the body.
•
Make sure that two or more people work together when using wires.
•
When using wires to remove the residual sealant, there may be
an interference between the nut hole and device hole. Thus, perform
sealant removal work as shown in the following figure:
Use a scraper or flathead driver to lift up a region between the body and panorama sunroof.
Turn and pull out wire (A)
between the nut hole and device hole (B) in the direction of the arrow.
Next, cut off the residual sealant again.
•
Be careful to avoid damaging the nut hole (C).
•
Be careful to avoid damaging the device hole (D).
14.
Cut residual sealant on every surface, and then remove panorama sunroof assembly (A).
•
Be careful to avoid damaging the panorama sunroof assembly when removing it.
Installation
•
In order to mount the panorama sunroof assembly, use the tools shown in the following figure:
[Tooling Diagram]
Sealant nozzle
Adhesive sealant for car windows
Sealant gun
1.
Use a blade to cut off residual sealant (A) around body panel.
•
When cutting off the residual sealant around the body panel,
make sure to leave about the thickness of 2mm from the adhesive surface.
•
Make sure that the body paint surface is not damaged at all.
•
If it is damaged, apply paint or rust inhibitor for maintenance.
2.
If panorama sunroof assembly (A) is reused, use a blade to remove residual sealant (B) around the body panel.
3.
Use alcohol or an air gun to clean up the edges of the body panel and the panorama sunroof.
4.
Use a sealant gun to apply sealant (B) around body panel (A).
•
When using a sealant gun to apply the sealant, make sure that the sealant is not cracked to prevent water leaks.
5.
Align with centering device hole (A) of the body, and carefully mount the panorama sunroof on the body panel.
[Front]
[Rear]
6.
Check step and gap before fully mounting panorama sunroof assembly (A).
7.
Apply tape to around the panorama sunroof assembly to prevent the assembly from coming off.
•
If sealant is excessively applied, it may ooze out of the
body. Use alcohol or a cleaning agent to wipe off the residual sealant.
Removal
1.
Open the roller blind using the panorama sunroof switch.
•
Leave 10 ~ 20cm (0.3937 ~ 0.7874 in) of the roller blind unopened.
2.
Remove t ...
Replacement
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Loosen the front door inside handle mounting screws (A).
3.
Using a flat-tip screwdriver (B), pull up the front door inside handle lock pin (C).
4.
Remove the front door inside handle (A).
5. ...
Systerm Circuit Diagram
With High Voltage Battery Heater System
Without High Voltage Battery Heater System
Circuit Diagram
Without High Voltage Battery Heater System
With High Voltage Battery Heater System
...